Most things that involve water flowing where it shouldn’t go would rank towards the top of a list of undesired concerns in a home. Water has the potential to be a highly damaging material, and it has a habit of generating invisible problems that only become obvious once they’ve progressed to the point of being dangerous. Your bathroom is a water hotspot and may cause a slew of problems, from ceiling leaks into rooms below to mould, wet, and even water leaking into fixtures.
Benefits of Bathroom Waterproofing
Prevents Dampness and Provides Insulation
The leaks are evident on the outsides of your walls and floors, but there are more problems beneath the surface that you cannot see. If you’re renovating your bathroom, you can discover moisture, plaster, or rotten-looking plywood after removing the tiles. If you locate any of these, they have almost certainly been in regular touch with water.
Adding a waterproof barrier between these surfaces and the top layer, such as tiles, can help prevent condensation and moisture from recurring. The advantages of bathroom waterproofing extend beyond the prevention of leaks and the production of damp. In fact, it is an excellent insulator. If your property’s external walls are linked to your bathroom, it becomes chilly, especially during the winter. This implies you’ll need a decent thermal unit to keep your bathroom warm. However, this might end up costing you a lot more in the long term. Waterproofing, on the other hand, can help keep your bathroom warm and even help you save money on your energy costs.
Increases Structural Value
As previously said, efficient bathroom waterproofing allows you to enjoy a variety of modern comforts and designs. Replacing outdated fixtures and basics with new ones can give your bathroom a whole new and refreshing design. Apart from the general state of a house, one aspect on which people like to focus is the condition of the bathrooms. When you already have an attractive bathroom, your chances of getting a good bargain are higher since it will increase the value of your home.
Pest and Mold Infestations
Mold and mildew are two of the most common moisture-related issues. Aside from the continuous cleaning necessary to keep mildew at bay, it tends to create serious health problems. Mold was shown to be the cause of virtually all chronic sinus infections in the United States (about 37 million), according to a 1999 research by The Mayo Clinic. It is known to cause allergies, rashes, and even asthma episodes due to the toxic chemicals released by fungus. Coughing, sneezing, and wheezing are just a few of the symptoms. Indoor mold is a severe health risk that may be avoided by properly sealing tile in places prone to moisture, whether in a household or commercial environment. Apart from that, moisture also draws common pests such as termites and carpenter ants, both of which may be quite damaging to your property. Pest infestations that go untreated may cause major structural damage throughout your house, but a proper moisture seal can help you avoid pest problems.
How to Waterproof your Bathroom?
Check Surface Adhesion
It is advised that you verify the bonding strength of the membrane before installing it by placing a tiny test strip (included) to the surface. Remove the strip’s protective wrapping and stick it to the wall. Pull the strip down from the wall while holding it at the fleece (grey).
Option 1: If the test strip moves position when pushing downward, pre-treat the surface with primer to improve adherence before proceeding with the installation.
Option 2: If the test strip sticks, skip the priming and utilize the sealing system instead.
Clean the area
Please make sure that the floors and walls are clean before beginning the installation procedure. All surfaces should be clean and free of adhesion-reducing contaminants to enable effective bonding (e.g. dust, acid, grease). Make sure the floor is grease-free and completely dry.
Apply corner pieces
Begin by putting the corner pieces in place. Make sure to use the (included) inner and outer corner pieces to cover all of them. Remove the foil off the bottom of the box and place the corner piece on the floor. In addition, remove the foil from the rest of the project and stick it to the wall. With the squeegee/spatula, apply pressure and eliminate any air pockets that may have formed.
Apply tape on corners
You need to cover all corners with the sealing tape. Remove the film, apply pressure and remove air pockets using the spatula. Make sure that the tape overlaps the corner pieces.
Apply membrane on walls
Remove around 10 centimeters of protective foil from the rear of the waterproofing membrane and work your way down. Always apply the membrane from top to bottom, overlapping the corner sealing tape if necessary. Make sure the membrane is placed accurately and any air pockets are removed using the spatula/squeegee. When removing the foil, take cautious not to harm the membrane.
Place some corner tape beneath the strip and overlap the next membrane on top of the tape. Use the finishing tape to cover the last strip of non-fleece material.
Washroom waterproofing is a common practice for houses as well as commercial structures where you require a clean and safe environment, free from pests and parasites of different kinds. Also, you don’t require any slippage or accidents to occur due to moisture present on the surface. The process is simple and can be done by a professional waterproofing company such as ours. Give us a call today and book your job.
If you want to know more about our website and services, visit (https://skychemicalservices.pk/)